34CrNiMo6 steel china supplier and stockholders, Otai special Steel supply of 34CrNiMo6 steel in round bar, flat bar, sheet, plate, and steel block. we can saw cutting 34CrNiMo6 steel as the size of your requirements. 34CrNiMo6 is an alloy engineering steel, the Delivery condition is Quenching and Tempered, Hardness 22 to 28HRc.
34CrNiMo6, 1.6582, 817M40, EN24 - Alloy steel
34Hnm, 34Chn1m, G35crimo6-6 DescriptionPhysical and Mechanical PropertiesHeat Treatment and WorkingWe Deliver This Steel Alloy asHighly hardeanable steel (more than 36HNM) that does not show tempering brittleness, which enables to create very strong and ductile parts thick up to 150mm. Cheaper alloys may be considered for thinner components for best cost/effect ratio. Steel used for highly stressed, impact-, torsion- and vibration-exposed parts, such as shafts, cranked shafts, press parts, heavily loaded rings, very large screws, such as cylinder cover screws for high-pressure steam turbines, rotors and discs for steam turbines, and all Products / Alloy Steel Plates / EN 10083-3 Alloy Steel EN10083-3 39MnCr. EN10083-3 39MnCrB6-2 STEEL PLATE Gangsteel Grade :EN10083-3 39MnCrB6-2 Specification (mm) THK:3 to 300, Width
BS EN 10083-1:2006 should be read in conjunction with BSEN 10083-2:2006 and BS EN 10083-3:2006. The standard does not cover bright steel products (see BS EN 10277 series) or continuously cast semi-finished products for which special arrangements must be made.
DIN EN 10083-1 Steels for quenching and tempering Together with Part 2 and Part 3 of this standard, this Part 1 is a revision of the following European Standards:EN 10083-1:1991 + A1:1996, Quenched and tempered steels Part 1:Technical delivery conditions for special steels EN 10083-2:1991 + A1:1996,
EN 34CrNiMo6 - Equivalent MaterialsThere are 64 equivalent materials for EN 34CrNiMo6 Alloy Steel. See the equivalents for ASTM, DIN, AFNOR, BS, UNI, SS, UNE, AISI, SAE, JIS, EN and GOST.
EN10083-3 42CrMo4 STEEL PLATE Gangsteel Grade :EN10083-3 42CrMo4 Specification (mm) THK:3 to 300, Width:1500 to 4050, Length:3000 to 27000 Standard:Technical delivery conditions for flat products of high yield strength structural steel
EN10083-3 51CrV4 alloy steel flat exporter - EN 10083-3 Grades:30CrNiMo8, 34CrNiMo6, 35NiCr6 Standard:EN 10083-3:2006 30CrNiMo8 material number:1.6580 34CrNiMo6 material number:1.6582 EN10083-3 38Cr2, 46Cr2 alloy steel strip sheet EN10083-3 20MnB5 steel is a hardening alloy steel for quenching and tempering.
France AFNOR 34CrNiMo6, NF EN 10083-1, NF EN 10083-3, France AFNOR NF EN 10083-1 NF EN 10083-3 NF EN 10250-3 NF EN 10263-4 NF EN 10269 NF EN 10277-5 NF EN 10343 34CrNiMo6 Steels for quenching and tempering for construction purposes - Technical delivery conditions and Mechanical Properties, Chemical Element, Cross Reference, Datasheet. AFNOR 34CrNiMo6 AFNOR 34CrNiMo6 Datasheet
EN 34CrNiMo6 Steel is an important alloy engineering steel grade as per BS EN10083-3:2006. 34CrNim06 steel has high strength, high toughness and good hardenability. EN / DIN 34CrNiMo6 alloy steel has the stability ofresistance to overheating, but the white sensitivity of 34CrNiM06 ishigh.
TECHNICAL DATA SHEET 34CrNiMo6 1 - dew-stahlstandards and designations din en 10083-3 1.6582 34crnimo6 din en 10263-4 1.6582 34crnimo6 b.s. 816m40 817m40 afnor 34crnimo8 35ncd6 uni 35nicrmo6kb jis sncm447 ss 2541 gost 38ch2n2ma din en iso 683-1 36crnimo6 aisi / sae / astm 4337 / 4340EN DIN 34CrNiMo6 1.6582 4337 Engineering Steel - QiLu EN 34CrNiMo6 Steel is an important alloy engineering steel grade as per BS EN10083-3:2006. 34CrNim06 steel has high strength, high toughness and good hardenability. EN / DIN 34CrNiMo6 alloy steel has the stability ofresistance to overheating, but the white sensitivity of 34CrNiM06 ishigh.